Wednesday, December 10, 2014


   This diy comes from www.pinkhousepages.blogspot.com .   A great idea to add some little vintage mini Christmas trees to your holiday display.

Vintage-look Bottle Brush Trees Tutorial

 Because some of my blog readers have asked "How the heck did you makethese?!?!?" I've invited the master-mind behind their creation to be a guest today and show you! Her name is Rosann, and she's one of those very clever people who can look at something, and figure out how to make it herself, and then actually make it out of, "oh just stuff I already have laying around the house."! You, however may need to go to the local hardware store to get the supplies, and here's Rosann now, to tell you what you'll be needing. Rosann--take it away, my friend.


Good morning Little Pink House readers! I'm excited to be here! Let's get going!

Supplies needed

sisal twine ~ your choice
wire ~ I like 26 gauge steel
rubber gloves
contact cement ~ dries clear
paper towels
tacky glue
vise ~ clamp type, (or just a drawer that shuts tightly - Jan)
paint brush ~ #12 flat is fine
items to decorate tree
wax paper

 First ~ protect your work surface. This will make for easy clean-up. Cut sisal into 3”to 4” lengths, then separate strains. Use as much or little for fullest and/or height of tree.Cut wire at least 20” long, then fold in half. Make a loop at top of wire with pencil turning 3 times. Remove pencil. With gloves on, put contact cement on both section of wire were the sisal will lay between.


 Center the sisal on one side of wire then place other half of wire on top, lining it up. (I felt like I needed two more hands at this point - Jan) Let cement set. 

 With ends of wire, place into the vise, tighten. With pencil back in loop, start to twist. You may need help the wire twist where sisal is, so use one hand to move sisal round it. Twist enough to hold firmly. Too much and the wire will break. (My first tree did break, but that's OK, it was still usable! - Jan)


 twist, twist and twist some more! This was the hardest part for me--getting the twists even throughout the wire, instead of bunching the twists at one end - Jan

 Remove tree (even though it doesn't look like one yet), from vise. Move sisal around to even out empty or full spots on tree.

 Start shaping the tree with scissors. Remove a little at a time on a 45 degree angle. Have the top of the tree towards you and work out to the base. (Kinda like that old joke about the marble sculpture--cut away anything that doesn't look like a tree ?!?!?)

 Keep the loop on the wire at the top to add a topper, otherwise it can be cut off. Trim wire at base, leaving as much as you need for base / stand.

 Lay a nice layer of mica on wax paper. This makes it easy to return unused mica to container. Brush tacky glue on tree, then roll over mica. May need to sprinkle some mica on by hand. (You could use glitter too, right? I wonder how German glass glitter would look!)

 Choose a base / stand for your tree. Then add on items with tacky glue to decorate the tree.(There are lots of options for the base. Rosann used 1/2 of a small Styrofoam ball, covered in flecks of gold glitter and the mica she used on the tree. You could use a wooden spool, or block too!) Or just anything you have laying around the house!

 Different twines will produce different trees. You can also dye the sisal to make trees for any season! Contact with water will also straighten out the twine as it dries. I used food coloring for my green trees (see picture at the top of this post) before I glued it to the wire, but I bet you could dip them afterwards too! How about PINK for Easter? And then you could glue tiny eggs to the tree, or...or...or...the possibilities are mind-boggling!
Important point: Some of the twines you find at the hardware stores are NOT SISAL, and don't work as well. They don't turn out as "full" and they won't "take up" any dyes. So be sure you have a true sisal (you can smell sisal, or just ask the sales person if you don't want any funny looks in the rope aisle at the hardware store).
PLEASE--if you make a tree, or a whole forest of them, email me to show us--we'd love to see what you've done! Rosann, thanks so much for showing my readers how to do this!
No problem, Jan. You can also check outwww.buildingmodeltrains.com/bottlebrush-trees/, for more instructions. If anyone has any questions you can email Jan and I'd be happy to answer them! Thanks for letting me sit in with you today!

No comments:

Post a Comment